Butterfly Valve Series

Product drawing»

Structural drawing»

You are here: News > News Detail

Butterfly Valve Flange Joint Leakage: Solutions, Gasket Replacement and Bolt Torque

2026-11-16

 In most cases the leak can be corrected without replacing the valve by renewing the gasket and applying the correct bolt torque.The main Butterfly Valve product names of China Butterfly Valve Network include:Electric Soft-sealed Flange Butterfly Valve,Electric Speed Control Butterfly Valve,Electric Vacuum Butterfly Valve,Electric Ventilation Butterfly Valve,Electric Serrate Regulate Butterfly Valve,Extended Hard-sealed Flange Butterfly Valve,Electric Desulfurization Wafer Butterfly Valve,Electric Desulfurization Flange Butterfly Valve,Fire Signal Butterfly Valve.

Identify the Cause Before Repairing

Before loosening any bolts, confirm that the leak originates at the flange joint and not at the stem packing or the body split line. Clean and dry the joint, then observe where fluid reappears. The most frequent causes are uneven bolt tightening, a compressed or hardened gasket, misaligned flanges, and excessive pipeline stress transmitted to the valve body. A gasket that has taken a permanent set or cracked from heat exposure cannot be restored by tightening and must be replaced.

Step 1: Isolate and Depressurize

Close the upstream and downstream isolation valves and relieve all pressure from the line section. Drain residual fluid and, for hot service, allow the joint to cool to ambient temperature. Never loosen flange bolts while the line is under pressure.

Step 2: Remove the Old Gasket

Loosen the flange bolts gradually in a crisscross pattern, a quarter turn at a time, to avoid distorting the valve body. Separate the flanges just enough to remove the old gasket. Clean both flange faces with a soft scraper and a compatible solvent. Remove all traces of the old gasket material, scale, and corrosion. Inspect the flange faces for radial scratches, pitting, or warping. A deeply scored flange face will not seal reliably even with a new gasket.

Step 3: Install the Correct Gasket

Select a gasket compatible with the process fluid and operating temperature. For water service, a compressed fiber or rubber gasket is common. For steam or high-temperature service, a spiral-wound or graphite gasket is required. The gasket inside diameter must match the flange bore, and the outside diameter must not obstruct the bolt holes. Position the gasket centrally between the flange faces without adhesive unless the manufacturer specifies otherwise.

Step 4: Tighten the Bolts to the Correct Torque

Tighten the flange bolts in a diagonal, crisscross pattern in at least three stages: approximately 30 percent, 60 percent, and 100 percent of the specified torque. This staged tightening compresses the gasket evenly and prevents body distortion. The correct torque value depends on bolt size, gasket type, and flange rating; typical values for DN100 PN16 butterfly valve flanges range from 60 to 90 Nm for M16 bolts with a compressed fiber gasket, but the valve manufacturer’s published torque table must always be followed. Do not exceed the specified torque, as over-tightening crushes the gasket and can crack the flange.

Step 5: Test the Joint

Pressurize the line slowly and check the joint for leakage. If a slight seepage appears, tighten the bolts in small increments rather than applying a large force at once. If leakage persists after correct torque and a new gasket, check flange alignment and pipeline stress.

Summary

Butterfly valve flange leakage is corrected by isolating the line, renewing the gasket, and tightening the bolts in a staged crisscross pattern to the manufacturer’s specified torque. Correct gasket selection and even bolt loading prevent recurrence. If leakage persists after these steps, misalignment or pipeline stress must be investigated before the valve is returned to service.

Do you still need to know or purchase the following Butterfly Valve products:

Kaiweixi Valve Group Co., Ltd
Kaiweixi Butterfly valve Contact Kaiweixi
Zhejiang Shanliu Valve Technology Co., Ltd
Shanliu Butterfly valve Contact Shanliu
ShangHai Meiyan Yi Pump & Valve Co.,LTD
Meiyan Yi Butterfly valve Contact Meiyan Yi
Shanghai Fengqi Industrial Development Co., Ltd.
FengQi Butterfly valve Contact FengQi